KK7DFL and KK7DFM

Two D-STAR repeaters feed XLX159 from the air: KK7DFL on 2m from Tumwater and KK7DFM on 70cm from Baw Faw Peak.

KK7DFL

145.275 MHz

Tumwater, Bush Mountain, Thurston County, WA · grid CN87ma

Checking link
Band
2m
Offset
−0.600 MHz
Uplink
144.675 MHz
CTCSS in / out
100.0 / 100.0 Hz
Modes
FM, D-STAR
D-STAR module
C
Trust server
USTRUST
Sponsor
South Puget Sound D-Star Club
WWARA ID
3240 (expires 2029-10-24)

Coverage. Local South Puget Sound coverage on 2m from Bush Mountain in Tumwater. Handheld coverage into Olympia, Tumwater and Lacey, and east into the I-5 corridor as far as Centralia and Chehalis.

Note. The workhorse for Olympia-area D-STAR. Module C is the one that feeds XLX159's cross-mode bridge most reliably.

KK7DFM

444.450 MHz

Chehalis, Baw Faw Peak, Lewis County, WA · grid CN86jl

Checking link
Band
70cm
Offset
+5.000 MHz
Uplink
449.450 MHz
CTCSS in / out
none
Modes
FM, D-STAR
D-STAR module
B
Trust server
USTRUST
Sponsor
South Puget Sound D-Star Club
WWARA ID
5633 (expires 2027-05-07)

Coverage. Wide area, roughly a 100 mile mobile radius from Baw Faw Peak (about 3,700 ft). Reaches Olympia, Centralia, Longview, Astoria, north Portland and south Seattle.

Note. The regional workhorse. Stations checking in from Tacoma, Longview or anywhere south of Olympia are usually on this one. Module B is the cross-mode hub.

D-STAR programming

What to put in RPT1, RPT2 and UR. Wrong values mean nobody hears you.

KK7DFL · 2m · module C

RPT1
KK7DFL C
Your local repeater. Always set this first.
RPT2
KK7DFL C
Same as RPT1 for a local contact, with no reflector linked.
RPT2 →
XLX159 B
D-STAR local RF, no XLX cross-mode.
RPT2 →
XLX159 D
Bridges to XLX159 module D.

KK7DFM · 70cm · module B

RPT1
KK7DFM B
Your local repeater. Always set this first.
RPT2
KK7DFM B
Same as RPT1 for a local contact, with no reflector linked.
RPT2 →
XLX159 C
Bridges to XLX159 module C.
RPT2 →
XLX159 D
Bridges to XLX159 module D.

When to link, and when not to

Most "is the repeater broken?" reports are really "somebody left a reflector linked for three days."

Do link when…

  • You want to reach a reflector or repeater outside local RF range. Set URCall to the reflector (for example XLX159 B) and RPT2 to the same string.
  • You are calling a specific station on another reflector. Set URCall to their callsign and RPT2 to the reflector you are calling through.
  • You hear a station say "listening on REF030 C" and want to join. Set URCall to CQCQCQ only after RPT2 is REF030 C and your radio is actually linked there.
  • You are on a hotspot on a different module from the station you are calling. Register at regist.dstargateway.org so your callsign routes across the trust network.

Don't link when…

  • You are having a local contact on RF. Leave URCall as CQCQCQ and RPT2 on your local repeater, so a two-minute chat does not go out to a whole reflector module.
  • You don't know what the last person left RPT2 set to. If you key up with it still in your radio, you are the one re-linking the repeater. Check before you transmit.
  • You are running a net on another module. Coordinate with net control, and have net control un-link at the end.
  • You are testing and unsure what your settings do. Use simplex or a test reflector. If you must test here, identify clearly and keep it under ten seconds.

Where this data comes from. Frequency, offset, tone, sponsor and coverage are from RepeaterBook (W7BR is the trustee for both), cross-checked against hearham.com. Both repeaters are coordinated by WWARA.

Found a discrepancy? If a frequency or tone has changed, Brent updates RepeaterBook first, then this page.

Maps © OpenStreetMap contributors.

Get in touch

Connection issues, net ideas, or a question about the reflector. Your message goes straight to the operator. Your email is only used so I can reply — never displayed publicly.

Sent directly to the operator. Nothing is stored on this site.